![]() ![]() Now who says there's no Santa Claus? Bah-humbug, indeed! So it seems the problems did not start with Windows 10 and also were not related to the Mojo. While I may not be ready to blow the All Clear signal just yet, after repeating this process 3 times on Christmas Eve my computer remains symptom free four days later. After much Googling I may have found a solution and it is very simple - just run the Windows Clean Boot procedure (msconfig) which is really easy to do, takes less than 5 minutes. Below is a copy of my eport to the support folk at Chord in the UK:Īfter suffering these issues pretty much all of December with increasing frequency and severity, my PC experienced some kind of “healing catharsis” last weekend. Unfortunately, new tricks are being served up almost every day! But this is a very good thing to regardless, I think. Great, I think I may have found a solution - Microsoft describes on their website how to perform a Clean Boot and that did the trick for me. Foobar cannot be made to work with this driver at all with any format source file (at least I can't get it to go). I am using J River Media Center as player. Selecting DSD on the Options panel doesn't work and as far as I can tell, there's no other way to activate DSD playback(?) To me, this indicates that there's nothing wrong with my Chord Mojo or its setup. It is, however, possible to "force" output to DoP 2.8 by selecting this option on the DSP panel. Unfortunately, DSD only works if set up to first convert to PCM (32-352.8) but it will not play DSD/DFF/FLAC natively. Otherwise, PCM stereo works great, I even think the sound quality is an improvement over the manufacturer's driver. Worse, there is some faint ticking noise, it is spurious and sort of like dust-on-the-needle if you can imagine that. The built-in sound card (Conexant 20671 SmartAudio HD) will not accept the new driver - I suppose it isn't 2.0 compliant - but reinstalling the factory driver was not a problem.įor music playback via the USB connector, I am using Chord Mojo which is capable of up 32-768 but this driver can "only" manage 32-384. Install NuPrime USB audio device driver again.Just posted this plea for help on the Microsoft feedback:īuild 14986: this update wipes 3rd party drivers off the computer and I haven't been able to re-install since the system keeps zapping it! Wouldn't be so bad if Audio 2.0 were perfect but it isn't.Go to Device Manager and look for any USB audio device driver (or any device driver) that has an error mark next to it.Uninstall NuPrime USB audio device driver.Unfortunately there is no simple solution to this problem. This is usually due to conflict with previously installed driver. Occasionally Windows users might encounter driver error or not able to install certain device driver files.For further information about how to configure the music player software for high resolution music playback, download this user guide:.Go to the System Preference/Setup and look for Sound device setup.Install the Windows device driver if it is required (Mac computer does not need to install USB Audio device driver). ![]() Connect the USB Audio device to the computer (before installing any device driver).Steps to setup your computer to use external USB Audio device such as a DAC (Digital to Analog Converter): This large amount of bandwidth available allows for USB audio interfaces to accommodate just about any recording or playback scenario imaginable. So, a stereo recording would take approximately 20 MB/second or 5 percent of the possible USB 2.0 bandwidth. To put this into perspective, 24 bit/192 khz audio–the highest bandwidth in commercial use–uses approximately 10 MB/second per track of audio. USB 2.0 can handle bandwidth of 480 MB/second. USB Audio devices do not need the bandwidth of USB3.0 and USB3.0 is backward compatible with USB2.0. A USB audio interface attaches to the computer with a standard USB connector and to the device itself with any number of other connectors, ranging from proprietary connections to standardized connections. Most USB audio interfaces are USB 1.0 and USB 2.0 compatible, so you should have no problem getting a device to work with any computer manufactured in the last 5 years. But if a DAC is connected to the smartphone, then the phone is now the host and the DAC is the client. So, if a smartphone is connected to a computer, the computer is the host and the phone is a client. The source device that produces the data is called the USB Host and the receiving end is the USB Client. USB Audio is a standard for digital audio used in PCs, smart phones and tablets to interface with audio peripherals. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |